View CBC915-ACA_3234460.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

?2011 cymbet corporation ? tel: +1-763-633-1780 ? www.cymbet.com ds-72-13 rev c page 1 of 15 cbc-eval-09 features cbc-eval-09 is a universal energy harvesting (eh) evaluation kit that combines any one of multiple eh transducers with the enerchip tm ep CBC915-ACA energy processor and the enerchip cbc51100 100uah solid state battery module that has two 50ah enerchip solid state batteries connected in parallel. the purpose of this evaluation platform is to enable designers to quickly develop energy harvesting applications. the eval-09 ships with a solar cell for initial evaluation kit testing. a photo of cbc-eval-09 board is shown in figure 1. system description there are several new technology advances on the eval-09: the ability to use any type of eh transducer, the enerchip energy processor that uses high energy effciency maximum peak power tracking algorithms, and enerchip solid state batteries for energy storage when the eh transducer is inactive. figure 1: cbc-eval-09 demo kit - 5 x 2 inches enerchip? ep universal energy harvester eval kit figure 2: enerchip cbc-eval-09 demo kit block diagram, with the cbc51100 enerchip 100uah module solar thermal em/rf vibration boost converter low voltage battery cutoff enerchip cbc51100 energy mgmt switching v out bridge rectifer energy processor CBC915-ACA low voltage charge pump flyback down converter low voltage charge pump dc in ac in bridge rectifers hv dc in hv ac1 in hv ac2 in pwm vdd serial i/o vreg feedback transducer vin select & sense vin sense txd rxd gnd enerchip cbc51100 module power out demo kit interface
cbc-eval-09 enerchip ep universal eh eval kit ?2011 cymbet corporation ? tel: +1-763-633-1780 ? www.cymbet.com ds-72-13 rev c page 2 of 15 eval-09 block diagram explanations this section describes the eval-09 functional blocks shown in figure 2. dc in - energy harvesting transducer input below 4.06v dc. normally a photovoltaic cell. ac in - energy harvesting transducer input below 4.06v ac. an example might be an electromagnetic input from a fow harvester . hv dc in - energy harvesting constant impedance transducer input from 4.06v dc to 20vdc. normally a photovoltaic cell or higher voltage thermoelectric generator. hv ac1 in and hv ac2 in - energy harvesting transducer input from 4.06v dc to 20v ac. normally a piezoelectric vibrational harvester. a single input can be utilized on hv ac1. if two piezo electric beams are mechanically coupled together in the same transducer unit, the two outputs can be connected to hv ac1 and hv ac2. bridge rectifers - rectifes from ac to dc for ac in or hv ac in. boost converter - boosts the dc in or ac in voltage to 4.06 volts. low voltage charge pumps (2) - used to start up the cbc915 energy processor. flyback down converter - drop hv dc in or hv ac1 in/hv ac2 in down to 4.06v. energy processor - enerchip ep cbc915 fnds the maximum peak power tracking point of the eh transducer input, transducer input voltage select and sense switches - monitors all input voltages and connects to the energy processor. enerchip cbc51100 solid state battery module - two enerchip 50uah solid state batteries (cbc3150 and cbc050) for energy storage. low voltage cut-off - should the voltage on the enerchips fall below 3.0vdc, this circuit disconnects the batteries so they do not discharge further. energy management switching matrix - controls the routing of vout to the system load. user selectable switches indicate the eh transducer input to voltage output. serial i/o - these 2 communications lines connect the energy processor to another microcontroller such as the ti msp430 mcu on the ez430-rf2500 demo kit wireless end device that would plug into connector j9.
cbc-eval-09 enerchip ep universal eh eval kit ?2011 cymbet corporation ? tel: +1-763-633-1780 ? www.cymbet.com ds-72-13 rev c page 3 of 15 j9 connector for user pin number(s) designation 1 rxd 2 gnd 3 not connected 4 not connected 5 v out 6 txd connector type: rt. angle sip j9 j10 j18 low voltage dc input pin number(s) designation 1 positive input 2 gnd connector type: 2 pin 100mil j10 connector for user pin number(s) designation 1 txd 2 rxd 3 v bat 4 gnd 5 v out connector type: vertical sip 1 1 cbc-eval-09 module connectors and switches enerchip cbc 51100 module j7 connector - external battery pin number(s) description 1,2 bypass diode connector type: circular pad j19 tp10 j17 high voltage ac input 2 pin number(s) designation 1 ac input 2 2 ac input 2 connector type: 2 pin 100mil figure 3: enerchip eval-09 connections, test points and switches j17 j16 j15 tp4 j18 tp11 1 2 3 4 o n 1 2 3 4 o n 1 2 3 4 o n tp2 tp1 tp8 tp9 tp5 tp3 sw1 sw3 sw2 j19 low voltage ac input pin number(s) designation 1 ac input 2 ac input connector type: 2 pin 100mil j15 high voltage dc input pin number(s) designation 1 positive input 2 gnd connector type: 2 pin 100mil j16 high voltage ac input 1 pin number(s) designation 1 ac input 1 2 ac input 1 connector type: 2 pin 100mil test points for user tp number designation 1 4.06v 2 epvcc 3, 4, 5 gnd 6 vcap 7 v out 8 vbat 9 vec 10 hv dc vin 11 dc vin connector type: clip lead tp7 tp6 j3 enerchip ep pins pin number(s) description 1-19 see cbc915 datasheet connector type: circular pad j4 enerchip ep pins pin number(s) description 20-38 see cbc915 datasheet connector type: circular pad j3 j4 j12 connector - external battery pin number(s) description 1 vextbat input 2 gnd connector type: circular pad j7 j12 s2 leds 1 u2
cbc-eval-09 enerchip ep universal eh eval kit ?2011 cymbet corporation ? tel: +1-763-633-1780 ? www.cymbet.com ds-72-13 rev c page 4 of 15 eval-09 module connector and test point explanations the purpose and use of the connectors identifed in figure 3 and in the previous tables are: j1, j2, j8, j11, j13, j14 connectors - not user accessible. j3 connector - enerchip ep pins 1-19 probe points and access vias. j4 connector - enerchip ep pins 20-38 probe points and access vias. j5. j6 connectors - eval-09 debug interface connectors for development system access. contact cymbet applications engineering for additional details if required . j7 connector - bypass diode circular pad trace to select an optional external rechargeable lithium battery with 4.1v charging voltage. j9 connector - six pin right angle connector for serial port, vout and ground. normally used for connection to ti ez430-rf2500 wireless end device or another target system. j10 connector - five pin vertical connector for user access to serial port, vout and ground. j12 connector - access vias for an optional external rechargeable lithium battery with 4.1v charging voltage. j15 connector - high voltage dc input from eh transducer such as a thermoelectric generator (teg). j16 connector - high voltage ac input 1 normally used by a piezoelectric eh transducer. j17 connector - high voltage ac input 2 normally used by a piezoelectric eh transducer . j18 connector - low voltage dc input normally used by a photovoltaic cell. j19 connector - low voltage ac input normally used by a thermoelectric generator or electromagnetic generator. cable assembly - a 5-conductor cable with a header connector at each end is provided with cbc-eval-09 to facilitate connection between the j5 connector and a 5-pin header on the users board. tp1 - the output of the boost converter or flyback converter capacitor. typical value is 4.06v. tp2 - epvcc - voltage used to power the cbc915 device should be 3.6v tp3, tp3, tp5 - ground tp6 C vcap C voltage of the output capacitor should be 3.6v tp7 C vout C output voltage to the target system should be 3.6v tp8 C vbat C output of battery cut-off circuit should be 4.06v tp9 C vec C enerchip output voltage feeding battery cutoff circuit should be in the range of 4.06vdc to 3.0vdc. caution: do not leave voltmeter or scope probes attached to this tp. will discharge enerchip. tp10 C hv v in C dc voltage from the hv dc in or hv ac1 in or hv ac2 in ports tp11 C v in C dc voltage from the dc in or ac1 in ports
cbc-eval-09 enerchip ep universal eh eval kit ?2011 cymbet corporation ? tel: +1-763-633-1780 ? www.cymbet.com ds-72-13 rev c page 5 of 15 eval-09 transducer input switch settings there are 3 dip slider switches on the eval-09 for use in selecting the energy harvesting transducer input to the rest of the on-board circuitry. the location of the switches are shown on the eval-09 layout diagram shown in figure 3. there can be only one eh transducer attached to the eval-09 at any time. combining transducer inputs is not supported. sw3 slide # off on 1 x 2 x 3 x 4 x sw2 slide # off on 1 x 2 x 3 x 4 x sw1 slide # off on 1 x 2 x 3 x 4 x photovoltaic (solar) cell transducer input selection on j18 sw3 slide # off on 1 x 2 x 3 x 4 x sw2 slide # off on 1 x 2 x 3 x 4 x sw1 slide # off on 1 x 2 x 3 x 4 x thermoelectric generator transducer input selection on j18 sw3 slide # off on 1 x 2 x 3 x 4 x sw2 slide # off on 1 x 2 x 3 x 4 x sw1 slide # off on 1 x 2 x 3 x 4 x electromagnetic/rf generator transducer input selection on j19 sw3 slide # off on 1 x 2 x 3 x 4 x sw2 slide # off on 1 x 2 x 3 x 4 x sw1 slide # off on 1 x 2 x 3 x 4 x piezoelectric generator transducer input selection on j16 and/or j17
cbc-eval-09 enerchip ep universal eh eval kit ?2011 cymbet corporation ? tel: +1-763-633-1780 ? www.cymbet.com ds-72-13 rev c page 6 of 15 eval-09 mode inquiry switch and led mode indicators a push button switch s2 as shown in figure 3 is used to display the eval-09 energy conversion state and charging status. there are 3 leds that indicate the 3 modes. mppt led (mppt) C maximum peak power tracking - indicates the energy processor is adjusting the input im - pedance to match the transducer impedance. any time the energy processor is performing the mppt function, the led will fash momentarily (1 millisecond). the led will be lit momentarily e very time the energy processor enters this state or when the push button is pressed. to force mppt state, hold s2 while connecting the eh transducer. when mppt led fashes, release push button switch s2. target system mcu or sw1 changes can also force mppt. output holding cap charge led (cap) C this indicates the capacitor used to hold output charge for the target load is being charged. the cap led will be lit momentarily every time the energy processor enters this state on its own, and in response to pressing s2 if in this state. enerchip charge led (ec) - this indicates the enerchip devices are being charged and power is turned on to the load. the led will be lit momentarily every time the energy processor enters this state, and state indicates the enerchips are being charged, but the system is not yet in regulation (e.g., due to insuffcient power being available). charge sequence complete - independent of the push button, once the energy processor has completed the sequence of mppt, cap charge and enerchip charge, all three leds will be fashed for 1 millisecond. in this state, system is in regulation. eval-09 output power disconnect C in order to remove the output voltage from the target load, press switch s2 and hold for 5 seconds. initially all three leds will fash (if the system was in regulation), or the ec led will fash (if the system was out of regulation). after 5 seconds, cap charge and ec charge leds will fash, indicat - ing the output voltage has been disconnected. a momentary press of switch s2 will indicate state information after the power has been disconnected from the load. eval-09 output power reconnect - in order apply output voltage to the target load, press switch s2 and hold for 5 seconds. initially all three leds will fash (if the system was in regulation), or the ec and mppt leds will fash (if the system was out of regulation). after 5 seconds, cap charge and ec charge leds will fash, indicat - ing the output voltage has been reconnected.
cbc-eval-09 enerchip ep universal eh eval kit ?2011 cymbet corporation ? tel: +1-763-633-1780 ? www.cymbet.com ds-72-13 rev c page 7 of 15 note that during the time the s2 push button is depressed no power is passed from the eval--09 to the target load. the following table provides a quick reference of the led indicators and their meaning. led mode description ec cap mppt maximum peak power tracking output holding capacitor charging enerchip charging normal operation; system in regulation output state change; fashes when s2 is held for 5 seconds output to load turned off; same as enerchip charging output to load turned off; system in regulation suggested energy harvesting transducers thermoelectric generators (tegs) - there are several vendors of thermoelectric generators. micropelt model mpg-d651 or mpg-d671 have been verifed with the cbc-eval-09. micropelts evaluation system is te- power plus, described on www.micropelt.com and available at mouser. nextreme also supplies a small teg, model eteg hv56 power generator. contact nextreme directly at www.nextreme.com. piezo electric generator - there are several vendors of piezoelectric generators. mide piezo units v20w, v25w, v21b, v21bl, v22b, and v22bl have been verifed with the cbc-eval-09. mides website is www.mide. com. another vendor is advanced cerametrics (aci). model numbers pfcb-w14, pfcb-w24, and pfcb-w54 will work with the eval-09. acis website is www.advancedcerametrics.com. alternate energy harvesting generators - new solutions for harvesting ambient energy are emerging from companies and universities worldwide. please contact cymbet applications engineering to discuss your requirements. connecting eval-09 to other vendors radio and microcontroller boards connectors j9 and j10 are designed to be connected to various microcontroller and radio boards from any of several vendors. for proper operation in energy harvesting environments, it is often necessary to load special frmware into the vendors target board. for information on downloading proper frmware for the texas instruments ez430-rf2500 target board, see cymbet application note an-1040: eval kit gui and ti ez430- rf2500 firmware readme, located on the cymbet website at http://www.cymbet.com/pdfs/an-1040.pdf.
cbc-eval-09 enerchip ep universal eh eval kit ?2011 cymbet corporation ? tel: +1-763-633-1780 ? www.cymbet.com ds-72-13 rev c page 8 of 15 operating characteristics specifcations subject to change without notice. (1) fluorescent (fl) light. (2) assuming charge rate is not limited by input power available from transducer. parameter condition min typical max units input luminous intensity (dc in; using pv panel provided) minimum operating lux 200 (1) - - lux full charge rate 700 (1) - - lux average continuous output power (measured at vout pin; using pv panel provided) 1000 lux (fl), battery not charging - 350 - w 200 lux (fl), battery not charging - 80 - w dc in operating voltage at transducer peak power point source impedance 100? to 200? 0.2 - 2.5 v source impedance >200? 0.5 - 4.0 v hv dc in operating voltage at transduc - er peak power point source impedance 10k? to 100k? 5.0 - 20 v dc in open circuit turn-on voltage 25c 0.4 - - v hv dc in open circuit turn-on voltage 25c 5.0 - - v ac in operating voltage at transducer peak power point source impedance 100? to 10k? 1.2 - 12 vpp hv ac in (1 and 2) operating voltage at transducer peak power point source impedance 10k? to 100k? 14.7 - 57 vpp quiescent current boost converter on - 20 - a boost converter off; ener - chips connected - 800 - na cbc915 off; enerchips connected - 115 - na vout ; 2 a load battery charged 3.5 3.55 3.6 v vchg charging voltage 25c - 4.06 - v battery cutoff voltage 4.7k? load 3.0 3.3 3.6 v pulse discharge current 20 msec - 30 - ma self-discharge (non-recoverable average) 25c - 2.5 - % per year operating temperature - 0 25 70 c recharge cycles (to 80% of rated capacity; 4.1 v charge voltage) 25c 10% depth-of-discharge 5000 - - - 50% depth-of discharge 1000 - - - 40c 10% depth-of-discharge 2500 - - - 50% depth-of-discharge 500 - - - recharge time (to 80% of rated 100ah capacity) (2) from 50% state-of-charge - 10 - minutes from deep discharge - 50 - minutes capacity 100a discharge; 25c 100 - - ah
cbc-eval-09 enerchip ep universal eh eval kit ?2011 cymbet corporation ? tel: +1-763-633-1780 ? www.cymbet.com ds-72-13 rev c page 9 of 15 eval-09 circuit schematics cbc51100 nc nc
cbc-eval-09 enerchip ep universal eh eval kit ?2011 cymbet corporation ? tel: +1-763-633-1780 ? www.cymbet.com ds-72-13 rev c page 10 of 15 eval-09 circuit schematics
cbc-eval-09 enerchip ep universal eh eval kit ?2011 cymbet corporation ? tel: +1-763-633-1780 ? www.cymbet.com ds-72-13 rev c page 11 of 15 cbc-eval-09 bill of materials the components on the eval-09 main board are as follows:
cbc-eval-09 enerchip ep universal eh eval kit ?2011 cymbet corporation ? tel: +1-763-633-1780 ? www.cymbet.com ds-72-13 rev c page 12 of 15 pulse discharge current for a wireless end device pulse discharge currents place special demands on batteries. repeated delivery of pulse currents exceeding the recommended load current of a given chemistry will diminish the useful life of the cell. the effects can be severe, depending on the amplitude of the current and the particular cell chemistry and construction. pulse currents of tens of milliamperes are common in wireless sensor systems during transmit and receive modes. moreover, the internal impedance of the cell often results in an internal voltage drop that precludes the cell from delivering the pulse current at the voltage necessary to operate the external circuit. this important issue is covered in cymbet applications note an-1025 available on cymbet.com. battery protection the eval-09 board contains a low battery cutoff circuit that prevents the enerchips on the cbc51100 module from being completely discharged - a condition that would permanently damage the battery. the cutoff circuit places a parasitic 400na load on the battery - a load that would discharge the two enerchips in approximately 125 hours, or just over 5 days. if the enerchips are allowed to reach the cutoff voltage at such low discharge currents, their specifed cycle life will be reached after a few hundred of such deep discharge cycles. to avoid this condition and extend the service life of the enerchip, it is advisable to program the mcu to count transmission cycles or elapsed time to determine when the enerchips state-of-charge is approximately 50%, at which time the mcu would force itself or another system circuit element to briefy draw high power from the cbc-eval-09, forcing the cbc-eval-09 circuit into a cutoff mode and thereby disconnecting the enerchips from the circuit. drawing a brief burst of a few milliamperes from the cbc-eval-09 will force the cutoff condition to occur within a few seconds. this will ensure that the charge/discharge cycle life of the enerchips will be greater than 5000, as rated. to calculate the number of hours the enerchips are capable of supplying energy to the load, add the cutoff current to the average load current drawn by the system and divide the sum into the combined 100ah capacity of the two enerchips. the quotient is the number of hours until the enerchip is totally depleted. divide that number in half to reach the 50% depth-of-discharge time. guidelines for attaching other energy harvesting transducers other energy harvesting transducers (e.g., inductive, piezoelectric, thermoelectric) may be attached to the cbc- eval-09. as confgured, the cbc-eval-09 will operate with many other transducer types. however, performance specifcations of these other transducers - namely output impedance - will affect the power conversion effciency of the cbc-eval-09 kit as designed. please contact cymbet applications engineering at the phone number shown below to discuss your specifc application and desired alternate transducer(s). system level considerations when using a low power energy harvester the eval-09 is capable of supplying 10s to 100s of w of continuous power to the load. most applications operating with radios and microcontrollers typically need 10s to 100s of mw of power under peak load conditions. the disparity between what is available and what is needed can be made up by limiting the amount of time the load is powered and waiting suffcient time for the energy harvester to replenish the energy storage device before the subsequent operation commences. in typical remote rf sensor applications, the on time will be on the order of 5-20ms, with an off time of several seconds to several hours depending on the application and available energy source. the duty cycle is an important consideration when designing a wireless system. while it is relatively straightforward to calculate a power budget and design a system to work within the constraints of the power and energy available, it is easy to overlook the power required to initialize the system to a known state and to complete the radio link with the host system or peer nodes in a mesh network. the initialization phase can sometimes take two to three times the power needed for steady state operation. ideally, the hardware should be in a low power state when the system power-on reset is in its active state. if this is not possible, the microcontroller should place the hardware in a low power state as soon as possible. after this is done, the microcontroller should be put into a sleep state long enough for the energy harvester
cbc-eval-09 enerchip ep universal eh eval kit ?2011 cymbet corporation ? tel: +1-763-633-1780 ? www.cymbet.com ds-72-13 rev c page 13 of 15 to replenish the energy storage device. if the power budget is not exceeded during this phase, the system can continue with its initialization. next, the main initialization of the system, radio links, analog circuits, and so forth, can begin. care should be taken to ensure that the time the system is on during this phase does not exceed the power budget. several sleep cycles might be needed to stair step the system up to its main operational state. the enerchip ep CBC915-ACA energy processor has a serial port to communicate to a microcontroller when energy is available. circuit recommendations to save power in most system power budgets, the peak power required is not as critical as the length of time the power is required. careful selection of the message protocol for the rf link can have a signifcant impact on the overall power budget. in many cases, using higher power analog circuits that can be turned on, settle quickly, and be turned off can decrease the overall energy consumed. microcontroller clock frequency can also have a signifcant impact on the power budget. in some applications it might be advantageous to use a higher microcontroller clock frequency to reduce the time the microcontroller and peripheral circuits are active. avoid using circuits that bias microcontroller digital inputs to mid-level voltages; this can cause signifcant amounts of parasitic currents to fow. use 10m to 22m pull-up/down resistors where possible. however, be aware that high circuit impedances coupled with parasitic capacitance can make for a slow rise/fall time that can place the voltage on the microcontroller inputs at mid-levels, resulting in parasitic current fow. one solution to the problem is to enable the internal pull-up/down resistor of the microcontroller input to force the input to a known state, then disable the resistor when its time to check the state of the line. if using the microcontrollers internal pull-up/down resistors on the inputs to bias push-button switches in a polled system, leave the pull-up/ down resistor disabled and enable the resistor only while checking the state of the input port. alternatively, in an interrupt-driven system, disable the pull-up/down resistor within the frst few instructions in the interrupt service routine. enable the pull-up/down resistor only after checking that the switch has been opened. microcontroller pull-up/down resistors are typically less than 100k and will be a huge load on the system if left on continuously while a button is being pressed or if held for any signifcant length of time. for even greater reduction in power, use external pull-up/down resistors in the 10m to 22m range. bias the external resistor not with the power rail but with a microcontroller port. the same algorithm used for internal pull-up/down resistors can then be used to save power. the charge line on the cbc5301 has a 10m pull-up resistor with a very slow rise time. use an internal microcontroller pull-down resistor to force the charge line low all of the time and then disable the pull-down resistor to check the state of the line. this will keep the charge line from biasing the input at mid level for long periods of time which could case large parasitic currents to fow.
cbc-eval-09 enerchip ep universal eh eval kit ?2011 cymbet corporation ? tel: +1-763-633-1780 ? www.cymbet.com ds-72-13 rev c page 14 of 15 frequently asked questions q: do i have enough input power from the eh transducer to charge the enerchip batteries? the cbc915 energy processor is initially started with charge pump u3 in piezo mode or u4 when in low voltage mode and accumulates enough charge into the cpout capacitors to then dump this charge in to the cbc915 vcc line. this action can be monitored on tp2 (epvcc) test point. the voltage will typically be around 2.5 volts and last for a few seconds if there is suffcient energy to operate the charge pump, but not enough energy to run the cbc915 energy processer. if there is suffcient energy to sustain the cbc915 energy processor, the tp2 voltage will start up at 2.5v and then jump up to approximately 3.5v. at this point the mppt led will fash indicating the cbc915 is entering the maximum peak power tracking state. checking tp1 4.06v for a voltage near 4.06 volts while the energy processer is fnding the mpp point will also give an indication if suffcient power is available. q: what if i short-circuit the output? a: the disconnect circuit will disconnect the enerchip devices from the output after the capacitor is discharged below 3.0v. this prevents the enerchips from being discharged too deeply. the enerchip device will automatically reconnect after the capacitor is recharged. q: what happens if i want to run a larger pulse current application? a: see application note an-1025. the eval-09 output capacitor bank can be sized to drive almost any load as long as the duration is not too long. an-1025 describes how to calculate the capacitor size. q: what happens if the enerchip is short-circuited? will it explode or leak harmful chemicals? a: no. there are no harmful chemicals to leak and the energy storage cells will not explode. q: how long will the cbc-eval-09 module operate with no ambient light? a: this depends on many factors, including load power consumption, enerchip state-of-charge, operating temperature, etc. the enerchips on the cbc51100 module provide 100ah of discharge capacity when fully charged. q: how long will the cbc-eval-09 module last if i use it every day and input power is available most of the time? a: the cbc-eval-09 module should last at least 10 years. q: how long will the two enerchips on the cbc51100 module hold a charge, assuming no input power? a: the self-discharge of the enerchip is a function of several parameters, including temperature. self- discharge specifcations can be found in the product data sheets at http://www.cymbet.com/content/ products-resource-docs.asp. q: what happens if the enerchip is left in a discharged state for a long period of time? a: leaving the enerchip in a discharged state is not detrimental to its performance. q: i see no voltage on vout. a: make sure there is suffcient input power to operate the cbc3150 charge pump and that the output is not short-circuited. q: will the cbc-eval-09 disconnect the enerchips before they become too deeply depleted? a: yes, the cbc-eval-09 has a cutoff circuit that will prevent the enerchips from being damaged due to over-discharge. however, repeatedly operating the system in a mode that allows the cutoff circuit to be invoked at deep discharge will cause premature capacity fade and shorter product life. if it is anticipated that the low voltage cutoff point will be reached, it is better to put the system into a high power mode to force cutoff at a higher state-of-charge, thereby prolonging the life of the enerchips. a :
cbc-eval-09 enerchip ep universal eh eval kit ?2011 cymbet corporation ? tel: +1-763-633-1780 ? www.cymbet.com ds-72-13 rev c page 15 of 15 cymbet, the cymbet logo and enerchip are trademarks of cymbet corporation. all rights reserved enerchip products and technology are covered by one or more patents or patents pending. disclaimer of warranties; as is the information provided in this data sheet is provided as is and cymbet corporation disclaims all representations or warranties of any kind, express or implied, relating to this data sheet and the cymbet battery product described herein, including without limitation, the implied warranties of merchantability, ftness for a particular purpose, non-infringement, title, or any warranties arising out of course of dealing, course of performance, or usage of trade. cymbet battery products are not approved for use in life critical applications. users shall confrm suitability of the cymbet battery product in any products or applications in which the cymbet battery product is adopted for use and are solely responsible for all legal, regulatory, and safety-related requirements concerning their products and applications and any use of the cymbet battery product described herein in any such product or applications. enerchip part number description notes cbc-eval-09 enerchip universal energy harvesting demo kit contains solar cell and cbc51100 module CBC915-ACA enerchip ep energy processor packaged in tape and reel or tubes cbc050-m8c enerchip 50uah solid state battery packaged in tape and reel or tubes cbc3150-d9c enerchip cc 50uah solid state battery with charge control packaged in tape and reel or tubes ordering information q: how can the eval-09 startup time be reduced and the time it takes the cbc915 to fnd the maximum peak power point? the eval-09 utilizes a seiko s-882z24-m5t1g charge pump to accumulate energy at startup and then dumps this energy into the cbc915 energy processor. once the cbc915 starts up, it automatically disables the seiko charge pump and operates a more effcient inductive boost converter. another approach to start the cbc915 when energy is available, is to pre-charge the on-board enerchips and then use the base of an npn bipolar transistor to sense when input voltage is available and tie the collector of the transistor into the cutoff circuit as a wired or. when energy is available from the energy harvesting transducer, the transistor will turn on and cause energy stored in the enerchips to initially power the cbc915 energy processor. this approach has the advantage of being instant on, but requires a board-level manufacturing process that can pre-charge the enerchips and requires a transducer to have a minimum of one forward pn junction voltage before the transistor will turn on. the charge pump method operates at a lower voltage but in the case of piezo electric transducers has a large impedance mismatch between the piezo element and the input into the charge pump so it can take a long time (several minutes) before enough charge is accumulated to dump into the cbc915 energy processor. the length of time the cbc915 takes to fnd the maximum peak power point is largely infuenced by the stability of the input signal generated by the energy harvesting transducer. mechanical transducers tend to have the most electrical input noise and consequently take the most time for the cbc915 to fnd the maximum peak power point. take steps to reduces noise such as flter capacitors in the several thousand microfarad range. after the frst time the cbc915 fnds the maximum peak power point, the coeffcients used to fnd the point are stored in memory. the next time the cbc915 is powered up it will use the coeffcients and not try to fnd the maximum peak power point again unless the system falls out of voltage regulation or is commanded to fnd the maximum peak power point by the application circuit microcontroller. a :

▲Up To Search▲

Price & Availability of CBC915-ACA

	To Download CBC915-ACA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .